Replacement cap OEC30-PSt7-NAU-OIW with oxygen sensor for OXYPro WR and WRM probes
SKU: OEC30-PSt7-NAU-OIW
Manufacturer: РreSens
Availability: Order only
The wide range PSt7 sensor is built into a beveled stainless steel cap. The design reduces the formation of air bubbles on the sensor with a very fast response time (
Maximum measuring range from 0 to 100% O2 (detection limit 0.03% O2 / 20 ppb).
This cap is not autoclavable.
Description Specifications Recommended products
Description
Description
The wide range PSt7 sensor is integrated in a stainless steel beveled cap. This cap reduces the formation of air bubbles on the sensor and provides a fast response time (
The OEC30-PSt7-NAU-OIW bolts to the body of the OXYPro WR / WRM probes to replace the used sensor and can be calibrated with one quick scan of the barcode. The replacement cap is not autoclavable.
- Maximum measuring range 0 - 100% O2
- Reduced air bubble formation
- Fast response time (
- Easy replacement thanks to barcode calibration
- Pressure resistant
Specifications
- Measuring range: Optimal: 0 - 50% O2, 0 - 500 hPa, 0 - 22.5 mg/L; Max: 0 - 100% O2, 0 - 1000 hPa, 0 - 45.0 mg/L
- Detection limit: 0.03% O2, 0.3 hPa, 0.015 mg/L.
- Compatibility: aqueous solutions, ethanol, methanol.
- No cross-sensitivity to: pH 1-14, CO2, H2S, SO2, ionic compounds
- Cross-sensitivity to: chlorine gas; organic solvents such as pure acetone, toluene, chloroform or methylene chloride
- Cleaning procedure: 3% H2O2, acidic substances (HCl, H2SO4) max. 4 - 5%; Cleaning agents containing ClO2 at room temperature.
- Calibration: two-point calibration in an oxygen-free environment (e.g. nitrogen 5.0, 1% sodium sulfite solution) and in an air-saturated environment (20.9% oxygen, air-saturated water)
- Pressure resistance: 10 mbar to 12 bar
- Operating temperature range: Optimal: from 0 °C to + 50 °C; Max: -10 °C to + 70 °C
Specifications
Application area | Process control |
Industry | Food and Beverage, Municipal |
Parameters | Dissolved oxygen |
Measurement Range | 0 - 22.5 mg/L O2 |
Operating temperature range | 0 - 50 °C |
Recommended products
Optical point SP-PSt6-YAU for oxygen sensor PreSens
The optical point is the most versatile version of optical oxygen sensors. Dissolved and gaseous oxygen is measured in a non-contact way through the transparent wall of the container. SP-PSt6-YAU has a measuring range of 0 to 5% oxygen in dissolved or gas phase.
SKU: SP-PSt6-YAU
LDO sc process dissolved oxygen sensor; cable 10 meters
LDO Process Dissolved Oxygen Sensor for SC Series Online Controllers. Available with 10 meter cable.
SKU: LXV416.99.20001
Orbisphere GA2400 Series Oxygen Sensor, 100 Bar
Electrochemical industrial oxygen sensor. Used in conjunction with Orbisphere controllers.
SKU: GA2400-S0S
LDO 2 sc dissolved oxygen process sensor for seawater, cable 10 m
Hach LDO® Model 2 Probe with Luminescent Dissolved Oxygen Technology for seawater.
SKU: LXV416.99.20S01
Needle micro oxygen sensor NFSG-PSt8
The NFSG-PSt8 Fixed Tip Micro Needle Oxygen Sensor is designed for headspace measurement of trace oxygen or other applications where small volume measurements of gaseous oxygen are required. Has a measurement range from 0 to 10% oxygen with a detection limit of 0.007% O2.
SKU: NFSG-PSt8
Optical point SP-PSt3-NAU for oxygen sensor PreSens
The optical point is the most versatile version of the non-invasive optical oxygen sensors. SP-PSt3-NAU has a measuring range from 0 to 100% oxygen in dissolved or gas phase
SKU: SP-PSt3-NAU
Inline oxygen sensor Orbisphere K1100 series, 0 - 40 ppm, 28 mm fitting
The Orbisphere K1100-S00H is a high-precision, fluorescent dissolved oxygen sensor optimized for energy applications.
SKU: K1100-S00H
Replacement cap OEC30-PSt3-NAU for OXYBase WR oxygen probe
Replaceable oxygen sensor for fast response times and reduced air bubbles for OXYBase WR probes.
SKU: OEC30-PSt3-NAU-OIW
Self-adhesive optical point SP-PSt3-SA for oxygen sensor PreSens
Optical point SP-PSt3-SA for non-invasive online monitoring of oxygen in the dissolved or gaseous phase in the range of 0 - 100%, 0 - 45 mg/l.
SKU: SP-PSt3-SA
Laboratory dissolved oxygen sensor LDO101, cable 1 m, 3 m
Intellical LDO101 - a digital luminescent / optical sensor of dissolved oxygen (LDO technology).
SKU: LDO10101, LDO10103
Oxygen sensitive PET bottle cap OSC-PSt3
The oxygen sensitive PET bottle cap PreSens OSC-PSt3 is designed to measure oxygen penetration into opaque bottles in the range of 0 - 100% O2, 0 - 1000 hPa / 0 - 45 mg/L, 0 - 1400 μmol/L.
SKU: OSC-PSt3
Replacement cap OEC30-PSt7-YAU with oxygen sensor for OXYPro WR and WRM probes
Thanks to the design of the cap, this model of the sensor reduces the formation of air bubbles during the measurement of dissolved oxygen.
SKU: OEC30-PSt7-YAU
Orbisphere M1100 inline oxygen sensor, 0 - 2 ppm, fitting 12 mm
Used in conjunction with Orbisphere controllers.
SKU: M1100-S10
Optical point SP-PSt7-NAU for oxygen sensor PreSens
Optical points SP-PSt7-NAU and SP-PSt7-YAU for PreSens oxygen sensors allow O2 measurements from 0 to 100% with a detection limit of 0.03%. SP-PSt7-NAU - not autoclavable. SP-PSt7-YAU - autoclavable.
SKU: SP-PSt7-NAU, SP-PSt7-YAU
Optical point SP-PSt9 for oxygen sensor PreSens
Optical point SP-PSt9 for non-invasive measurement of ultra-low oxygen content in the range of 0 - 200 ppmv O2, with a detection limit of 0.5 ppmv oxygen.
SKU: SP-PSt9-NAU-D3-OIW
Oxygen Probe for In-Line Measurement OIM-PSt3
PreSens OIM-PSt3 is designed for process control and provides accurate and stable O2 measurements in the 0-100% / 0-45 mg / L range, with a detection limit of 0.03% / 15 ppb.
SKU: OIM-PSt3
Oxygen sensitive PET bottle cap OSC-PSt6
The oxygen sensitive PET bottle cap PreSens OSC-PSt6 is designed to measure oxygen penetration in colored bottles in the range of 0 - 5% O2 / 0 - 2 mg/l.
SKU: OSC-PSt6
Optical point SP-PSt8-NAU for oxygen sensor PreSens
Optical points SP-PSt8-NAU and SP-PSt8-YAU for PreSens oxygen sensors allow O2 measurement in the range from 0 to 10%, detection limit - 0.007%. SP-PSt8-NAU - not autoclavable. SP-PSt8-YAU - autoclavable.
SKU: SP-PSt8-NAU, SP-PSt8-YAU
Orbisphere M1100 inline oxygen sensor, 0 - 40 ppm, fitting 12 mm
Used in conjunction with Orbisphere controllers.
SKU: M1100-S10H
Oxygen Probe for In-Line Measurement OIM-PSt6
PreSens OIM-PSt6 is designed for process control and provides accurate and stable O2 measurements in the 0-5% / 0-2 mg/L range, with a detection limit of 0.002% / 1 ppb.
SKU: OIM-PSt6
Replacement cap with oxygen sensor OEC-PSt7-NAU for OXYPro WR and WRM probes
Fast response oxygen sensor for PreSens OXYPro WR and WRM probes.
SKU: OEC-PSt7-NAU-OIW
Orbisphere M1100 inline oxygen sensor, 0 - 40 ppm, fitting 28 mm
Used in conjunction with Orbisphere controllers.
SKU: M1100-S00H
Orbisphere M1100 inline oxygen sensor, 0 - 2 ppm, 28 mm fitting
Used in conjunction with Orbisphere controllers.
SKU: M1100-S00
Inline oxygen sensor Orbisphere K1100 series, 0 - 2000 ppb, 28 mm fitting
The Orbisphere K1100 is a high-precision, fluorescent dissolved oxygen sensor optimized for energy applications.
SKU: K1100-S00
Recommended products
Needle micro oxygen sensor NFSG-PSt8
The NFSG-PSt8 Fixed Tip Micro Needle Oxygen Sensor is designed for headspace measurement of trace oxygen or other applications where small volume measurements of gaseous oxygen are required. Has a measurement range from 0 to 10% oxygen with a detection limit of 0.007% O2.
SKU: NFSG-PSt8
Inline oxygen sensor Orbisphere K1100 series, 0 - 40 ppm, 28 mm fitting
The Orbisphere K1100-S00H is a high-precision, fluorescent dissolved oxygen sensor optimized for energy applications.
SKU: K1100-S00H
Orbisphere M1100 inline oxygen sensor, 0 - 2 ppm, 28 mm fitting
Used in conjunction with Orbisphere controllers.
SKU: M1100-S00
Replacement cap OEC30-PSt3-NAU for OXYBase WR oxygen probe
Replaceable oxygen sensor for fast response times and reduced air bubbles for OXYBase WR probes.
SKU: OEC30-PSt3-NAU-OIW
Orbisphere M1100 inline oxygen sensor, 0 - 40 ppm, fitting 12 mm
Used in conjunction with Orbisphere controllers.
SKU: M1100-S10H
Replacement cap OEC30-PSt7-YAU with oxygen sensor for OXYPro WR and WRM probes
Thanks to the design of the cap, this model of the sensor reduces the formation of air bubbles during the measurement of dissolved oxygen.
SKU: OEC30-PSt7-YAU
OXYBase WR-RS485 and WR-RS485M sensors for measuring gaseous and dissolved oxygen
OXYBase® WR-RS485 and WR-RS485M combine an optical sensor of the PSt3 type and an electro-optical module in one probe. The maximum measuring range is 0 - 100% O2 and the detection limit is 0.03% O2.
SKU: WR-RS485, WR-RS485M
Orbisphere M1100 inline oxygen sensor, 0 - 2 ppm, fitting 12 mm
Used in conjunction with Orbisphere controllers.
SKU: M1100-S10
Oxygen Probe for In-Line Measurement OIM-PSt3
PreSens OIM-PSt3 is designed for process control and provides accurate and stable O2 measurements in the 0-100% / 0-45 mg / L range, with a detection limit of 0.03% / 15 ppb.
SKU: OIM-PSt3