998 (90) 174-57-84
Optical point for M1100 and K1100 dissolved oxygen sensors
SKU: M1100-L, M1100-H
Manufacturer: Orbisphere
Availability: In stock
Dedicated optical contact pad (sensing element) for the Orbisphere M1100 and K1100 dissolved oxygen sensors:
- M1100-L low measuring range 0 - 2000 ppb
- M1100-H high measuring range 0 - 40 ppm
Scope of delivery: optical point and O-ring.
Description Specifications Recommended products
Description
Description
The optical point must be replaced about once a year. It is recommended to calibrate the sensor every 6 months if used in the beverage industry using CIP. The procedure is very simple and takes no more than a couple of minutes. Depending on the oxygen measuring range, the sensor life may be shortened and the frequency of maintenance and calibration may increase. If bleaching compounds and strong oxidants (such as ClO2) are present in the sample, sensor life may also be shortened.
Removing the optical point (sensitive element)
- Slide the maintenance tool (straight edges on top) as far as possible over the old optical point. Continue to push and twist the tool until the straight edges of the tool fit into the straight grooves on the sensor.
- When the instrument is in the desired position, turn it counterclockwise to unscrew the old optical point.
- After unscrewing it completely, simply remove it. Remove the tool for maintenance and discard the old optical point of the sensor.
Note: check the o-ring. If it is damaged, remove it with tweezers and replace with a new one from the maintenance kit.
Optical point replacement
Important: During the replacement process, avoid scratching or damaging the sensor (black surface on the sensor head).
- Slide the maintenance tool (straight edges on top) as far as possible over the new optical point. Continue to push and twist the tool until the straight edges of the tool fit into the straight grooves on the sensor
- Make sure the sensor collar is as far down as it will go, so that the top of the collar is aligned with the base of the sensor head.
- Take the combined maintenance tool and sensor spot and place it in the end of the sensor.
- Turn the tool clockwise to screw in the optical point. Do not over tighten. Once securely in place, remove the service tool.
Specifications
| Application area | Brewing, Beverages, Process control |
| Type | Industrial |
| Industry | Food and Beverage |
| Parameters | Dissolved oxygen |
Recommended products
Replacement cap for dissolved oxygen sensor LDO 2 sc
Process Dissolved Oxygen Sensor Cap Replacement Kit.
SKU: 9021150
Compare
Cuvette Hach round 1 inch (25 mm), 6 pcs. 10 mL each
Sample Cell. Use with Hach colorimeters and spectrophotometers.
SKU: 2427606
LDPE sampling bottle, 250 mL, 12/pc
Bottle for sampling is made of low-density polyethylene (LDPE), 250 mL. A package contains 12 bottles.
SKU: 2087076
SKU: 004.413
Plastic tubes with caps, 4 pieces
Tubes for colorimetric analysis of water.
SKU: 4660004
Sample Cell: Square 25 mm (1 inch) Polystyrene 25mL with Caps
Cuvette for the analysis of liquids on a spectrophotometer. The optical path length is 25 mm (1 inch).
SKU: 2410222, 2410212
Crimp caps with pre-installed septa for vials, 20 mm
20 mm aluminum crimp caps for chromatography vials with pre-installed septa.
SKU: #20PTFE/White Silicone
SKU: 001.048
Hach rectangular cuvettes 50 mm, 10 pcs. PMMA
Sample cuvette, polystyrene, 50 x 10 mm, optical path 50 mm, minimum volume 5.0 ml, with lids, pack contains 10 pcs.
SKU: LZP341
Flow sensor for TU5300sc and TU5400sc laser turbidity meters
The addition of flow measurement to the TU5300sc or TU5400sc on-line turbidity analyzers provides important information on the status and quality of the potable water production process.
SKU: LQV160.99.00002
Replacement cap for LDO dissolved oxygen sensors
For Hach laboratory and field sensors LDO101 series.
SKU: 5811200
Glass cuvette for samples 25 mm., 6 pieces with caps
Sample cuvette. For use with Hach DR900 colorimeter.
SKU: 2401906
Molded gray septa 20 mm, PTFE / butyl
20mm molded gray butyl PTFE septa are widely used in the pharmaceutical industry.
SKU: #20PTFE/Butil
Cartridge for digital titrator, empty
Hach Handheld Digital Titrator Cartridge (1690001).
SKU: 1449501
Deuterium Lamp
Deuterium (UV) lamp. Suitable for use with Hach DR5000, DR6000 spectrophotometers.
SKU: A23792
Amtax sc analyzer electrode maintenance kit
The kit contains 3 bottles of electrolyte and 3 membranes for the AMTAX sc ammonium analyzer for ranges 2, 3, 4 (0.05 - 1000 mg/L NH4-N).
SKU: LCW868
DR Hach Spectrophotometers Filter Set
Consists of filters to check absorption accuracy, stray light and wavelength accuracy. Designed for use with a standard 10 mm cuvette holder. The set is supplied in a sturdy wooden case.
SKU: LZV537
SKU: 51105600
Quartz square sample cell, 10 mm
Quartz glass sample cuvette, 10 x 10 mm, path length 10 mm, volume = 3.5 ml. Supplied with caps, matched pair or 1 piece.
SKU: 2624410, 4822800
Cl17 Chlorine Analyzer Maintenance Kit
Pre-assembled tubing for annual maintenance of the Hach CL17 chlorine analyzer.
SKU: 5444301, 4721600
Pocket Pro+ Replacement sensor for Multi parameter tester 2
For Pocket Pro+ Multi parameter tester 2 only.
SKU: 9532801
Service kit for BioTector 3500 19-KIT-123
Replacement set for maintenance, interval 6 months.
SKU: 19-KIT-123
Tungsten Lamp
Tungsten lamp (incandescent lamp). Suitable for use with Hach DR5000, DR6000 spectrophotometers.
SKU: A23778
Glass cuvette Hach square 1 inch (25 mm), 2 pcs.
Photometric vials. For use with Hach DR1900, DR6000, DR3900 spectrophotometers.
SKU: 2495402, 2495408
Related products
Orbisphere M1100 inline oxygen sensor, 0 - 2 ppm, fitting 12 mm
Used in conjunction with Orbisphere controllers.
SKU: M1100-S10
Orbisphere M1100 inline oxygen sensor, 0 - 40 ppm, fitting 28 mm
Used in conjunction with Orbisphere controllers.
SKU: M1100-S00H
Inline oxygen sensor Orbisphere K1100 series, 0 - 2000 ppb, 28 mm fitting
The Orbisphere K1100 is a high-precision, fluorescent dissolved oxygen sensor optimized for energy applications.
SKU: K1100-S00
Inline oxygen sensor Orbisphere K1100 series, 0 - 40 ppm, 28 mm fitting
The Orbisphere K1100-S00H is a high-precision, fluorescent dissolved oxygen sensor optimized for energy applications.
SKU: K1100-S00H
Show more
Recommended products
SKU: 001.048
AutoSampler 2.0 for ZEUTEC SpectraAlyzer analyzers
The ZEUTEC AutoSampler 2.0 is used in conjunction with the liquid analysis compartment (Liquid Drawer) of the SpectraAlyzer analyzer. Simplifies compositional analysis of samples using near infrared reflectance characteristics.
SKU: 103-A100-1
UV protection housing for SC4200c and SC4500 controllers
Sun protection housing for SC controllers.
SKU: LXZ524.99.00005
2084900 Glass cell for laboratory turbidity meters, 30 ml, 6 pcs. with caps
Glass cuvette for samples. Used for turbidimeters 2100N, 2100AN and Lab RATIO.
SKU: 2084900
Peristaltic pump ZEUTEC
The ZEUTEC pump is used in conjunction with a liquid analysis drawer for SpectraAlyzer 2.0 analyzers. Due to its small size, the pump can be placed on a bench next to the analyzer or on the instrument itself for easy access.
SKU: 104-A100-1
Crimp caps with pre-installed septa for vials, 20 mm
20 mm aluminum crimp caps for chromatography vials with pre-installed septa.
SKU: #20PTFE/White Silicone
SKU: 2810 0100
Plastic sample container, 120 ml, 250 pcs
Hermetic container for collecting samples, 120 ml. The number of containers in a package is 250 pieces.
SKU: 2552212
Cl17 Chlorine Analyzer Maintenance Kit
Pre-assembled tubing for annual maintenance of the Hach CL17 chlorine analyzer.
SKU: 5444301, 4721600
