998 (90) 174-57-84
HI7061L Universal pH Electrode Cleaning Solution (500 ml)
SKU: HI7061L
Manufacturer: Hanna Instruments
Availability: In stock
HI7061L is a general purpose cleaning solution for use with pH and ORP electrodes.
Cleaning is a quick and effective procedure that should be performed on a regular basis as a preventive measure to prolong the life of the sensor and to ensure that the connection is not clogged. Simply immersing the electrode in the HI7061L cleaning solution for 15-20 minutes will dissolve any mineral deposits or other coatings.
Description Specifications Recommended products
Description
Description
Hanna HI7061L Universal Cleaning Solution for cleaning pH electrodes and ORP sensors
The electrodes can become dirty in use and will give inaccurate results even if they read correctly when immersed in pH buffer. Hanna cleaning solutions remove dirt and residues that remain on the surface of electrodes when immersed in samples during measurement or improperly stored. It is recommended that you clean the bulb and connection of your electrode regularly to keep it clean and to prevent clogging of the connection.
The most common cause of inaccurate pH measurement is a dirty or improperly cleaned electrode. This is very important to note because during calibration the instrument assumes that the electrode is clean and that the standardization curve created during the calibration process will remain a valid reference until the next calibration. If the mV offset continues to deviate and the instrument is calibrated with a dirty electrode, this will result in inaccurate readings.
Specifications
| Quantity |
Recommended products
51340036 Electrolyte for GSE Ammonia Electrode
Electrolyte to ensure stable operation and accurate measurements by the GSE Ammonia Electrode.
SKU: 51340036
Compare
51340029 Electrolyte for DX280-Br electrode
The electrolyte serves to create a stable and well defined electrochemical environment within the DX280-Br ion selective electrode.
SKU: 51340029
Calibration solutions for TDS meters 1000 ppm
A solution of Na2SO4, Na2CO3, NaCl for checking the accuracy of instruments when measuring conductivity and total dissolved solids (salt content) of water.
SKU: 2974726, 2974749
ISE standard solution, Fluoride (F-) concentration 100 mg/l; volume 500 ml
Standard Fluoride Ion Selective Electrode (ISE) solution for laboratory analysis.
SKU: 23249
ISE standard solution, Fluoride (F-) concentration 1 mg/l; volume 500 ml and 1 liter
Standard Fluoride Ion Selective Electrode (ISE) solution for laboratory analysis.
SKU: 29149, 29153
51350004 pH 4.01 Technical buffer solution
pH buffer with pH value 4.01 ± 0.02 for electrode calibration.
SKU: 51350004
NaCl solution for conductivity meter calibration 1990 μS/cm, 100 mL
Standard solution for tds and conductivity meters.
SKU: 210542
51350042 Certified Buffer pH 4.01 6 x 250 ml
pH buffer for electrode calibration. The package contains 6 bottles of 250 ml.
SKU: 51350042
51350078 Electrolyte KNO3 1M; 250 ml
Solution 51350078 is recommended for use with Mettler Toledo DX Series electrodes for the determination of ammonium, potassium and nitrate.
SKU: 51350078
51302070 Buffer pH 9.21 in sachets 30x20 ml
Disposable pH buffer sachets from Mettler Toledo. The solution is poured into the package under controlled conditions, ensuring a fresh and clean solution for every pH electrode calibration.
SKU: 51302070
51340035 Electrolyte for DX218-NH4, 20 ml
Solution for filling the DX218-NH4 electrode.
SKU: 51340035
30111137 Buffer pH 6.865 sachets 30x20 ml
Sealed sachets with fresh pH buffer solution for single use.
SKU: 30111137
ISE standard solution, Fluoride (F-) concentration 2 mg/l; volume 500 ml
Standard Fluoride Ion Selective Electrode (ISE) solution for laboratory analysis.
SKU: 40520
51350046 Buffer pH 9.21, 6 x 250 ml
Solution with a standard pH value of 9.21±0.02
SKU: 51350046
KCl calibration solution for conductivity meters 1412 μS/cm
Calibration solutions are designed to adjust the measurement accuracy of instruments when measuring the electrical conductivity of water.
SKU: 2974326, 2974349
51350108 Ionic Strength Adjustor 0.9 mol/L Al2(SO4)3, 250 ml
Accurate ion determination requires the correct solution (ISA) to adjust ionic strength. This solution is used in determining the concentration of nitrate, fluoroborate, lithium, ammonium and potassium ions.
SKU: 51350108
Certified Buffer Standard Solution, pH 1.679
Certified Buffer Standard Solution,1.679 ±0.010 pH at 25°C.
SKU: S11M001
51343180 Electrolyte KCl 3M 25 ml
Electrolyte for filling the ph electrode.
SKU: 51343180
Buffer Solution, pH 7,00
Buffer Solution, concentration pH 7,00± 0,02, 500 mL.
SKU: 1222249
ISE Ammonia Standard Solution, 100 mg/L, 500 mL
ISE Standard Solution. Ammonia, 100 mg/L ±2 mg/L NH3-N. 500 mL bottle.
SKU: 2406549
Powder Pillows buffer, pH 10.01 blue 250 pcs.
Standard for the calibration of electrodes. pH buffer in powder for dilution. The color coding is blue.
SKU: 2227164
Powder Pillows pH buffer sachets 4.01 (red)
Color-coded powder pH buffer for pH electrode calibration.
SKU: 2226966
Conductivity Standard Solution, 146,9 µS/cm
Calibration solution, concentration 146.9 μS/cm ± 2.5% at 25 °C / 0.001M KCl, 500 ml.
SKU: C20C280
Conductivity calibration solution 10000 μS/cm, NaCl, 50 ml
Standard solution for calibrating TDS meters and conductivity meters.
SKU: 2972226
Recommended products
Powder Pillows sachets with buffer pH 10.01 (blue) 50 pcs.
Standard for calibrating pH electrodes.
SKU: 2227166
51350020 Calibration solution pH 7.00, 6 x 250 ml
Buffer solution with a pH value of 7.00 ± 0.02 for calibrating pH meters and electrodes.
SKU: 51350020
HI70300L pH electrode storage solution (500 ml)
HI70300L is an electrode storage solution formulated with chemicals that can be used to keep your pH and ORP electrodes performing optimally. When the pH electrode is stored properly in solution, the glass membrane is well hydrated, which ensures proper functioning and accurate readings.
SKU: HI70300L
Buffer solution pH 10.01, 125 ml
Calibration solution with pH 10.01 ± 0.02 at 25 ° C for ph electrodes.
SKU: LZW9470.99
30090860 Ammonium standard solution 100 mg/l
A pre-mixed solution with an accurately known concentration of ammonium (NH4) is commonly used to calibrate and verify the accuracy of ion selective electrodes.
SKU: 30090860
ISE standard solution, Fluoride (F-) concentration 2 mg/l; volume 500 ml
Standard Fluoride Ion Selective Electrode (ISE) solution for laboratory analysis.
SKU: 40520
51107885 Electrolyte for DX224-Mg 20 ml
Electrolyte for ion-selective electrode determining Magnesium ions.
SKU: 51107885
Singlet Single-use Conductivity Standard Solution, 1413 µS/cm
Singlet standard solutions for calibration of conductometers in individual sealed bags, without color coding. Packaging: 20 sachets, 20 mL each.
SKU: 2771420
51344762 PerfectION potassium ISA, 475 ml
Ionic strength adjuster for obtaining accurate readings from an ion-selective electrode that determines the concentration of potassium.
SKU: 51344762
