998 (90) 174-57-84
Replacement cap for dissolved oxygen sensor LDO 2 sc
SKU: 9021150
Manufacturer: Hach
Availability: Order only
Replacement Sensor Cap Kit for process Dissolved Oxygen Sensor LDO 2 sc.
Description Specifications Recommended products
Description
Description
The sensor setup cap is not waterproof, do not perform the replacement procedure if the sensor is immersed in water. Always keep the inside of the sensor setup cap dry. After installing a new cap, an error may be displayed on the controller screen. On sc100 and sc200 controllers, the error condition resolves after 1 to 2 minutes. Make sure the lot of the setup cap matches the lot of the sensor cap.
Step-by-step instructions for replacing 9021150 for LDO sc 2 sensor:
- Make sure the sensor is connected to the controller and the power is ON.
- Clean the sensor.
- Remove and discard the old sensor cap.
- Install the sensor setup cap.
- Press the button on the setup cap. The indicator will light up for 45 seconds, then it will start blinking: single flashes - 10 times, the installation was successful -> go to step 6. Double blinks 38 times, remove sensor setup cap -> repeat steps 6, 4 and 5.
- Remove the sensor setup cap. Store in a dry place.
- Install a new sensor cap. Validate the sensor cap code: Make sure that the cap lot shown on the display and the cap lot on the cap are the same.
Specifications
| Application area | Environmental monitoring, Wastewater, Treatment facilities, Equipment for water utilities, Process control |
| Type | Industrial |
| Industry | Ecology, Municipal |
| Parameters | Dissolved oxygen |
Recommended products
SKU: 12-0308
Compare
DR Hach Spectrophotometers Filter Set
Consists of filters to check absorption accuracy, stray light and wavelength accuracy. Designed for use with a standard 10 mm cuvette holder. The set is supplied in a sturdy wooden case.
SKU: LZV537
Polymer Optical Fiber for PreSens Measuring Instruments
Polymer optical fiber serves as a universal connector between the meter and the PreSens. POV with SMA connector is compatible with Fibox, OXY-1 SMA, OXY-1 WM, OXY mini and pH mini meters, as well as pCO2 mini. POF with ST connector is compatible with Microx 4 and OXY-1 ST series meters.
SKU: POF
LDPE sampling bottle, 250 mL, 12/pc
Bottle for sampling is made of low-density polyethylene (LDPE), 250 mL. A package contains 12 bottles.
SKU: 2087076
Amtax sc analyzer electrode maintenance kit
The kit contains 3 bottles of electrolyte and 3 membranes for the AMTAX sc ammonium analyzer for ranges 2, 3, 4 (0.05 - 1000 mg/L NH4-N).
SKU: LCW868
Crimp caps with pre-installed septa for vials, 20 mm
20 mm aluminum crimp caps for chromatography vials with pre-installed septa.
SKU: #20PTFE/White Silicone
Delivery tubes for Digital Titrator, 5 pk
Delivery tubes for Hach Handheld Digital Titrator (1690001).
SKU: 1720500
Sunroof visor for SC4200c and SC4500 controllers
Visor for controllers protection from changes in weather conditions.
SKU: LXZ524.99.00033
SKU: 006.963
SKU: 006.593
Hach rectangular cuvettes 50 mm, 10 pcs. PMMA
Sample cuvette, polystyrene, 50 x 10 mm, optical path 50 mm, minimum volume 5.0 ml, with lids, pack contains 10 pcs.
SKU: LZP341
Adapter A for DR3900 Spectrophotometer
Replacement adapter for sample cells.
SKU: LZV846
Glass square sample cell 25 mm, matched pair
Accessory for spectrophotometers / spectral analysis of liquids.
SKU: 2095000
Flow sensor for TU5300sc and TU5400sc laser turbidity meters
The addition of flow measurement to the TU5300sc or TU5400sc on-line turbidity analyzers provides important information on the status and quality of the potable water production process.
SKU: LQV160.99.00002
Rectangular plastic cuvette, 10 mm; 100 pieces
Disposable 1.5 ml cuvettes; packing of 100 pieces.
SKU: 2629500
Pocket Pro+ Replacement sensor for Multi parameter tester 1
For Pocket Pro+ Multi parameter tester 1 only.
SKU: 9532701
White caps for Culture Tube
The Hach screw cap uses a durable seal to ensure the vial is tight.
SKU: 2275800, 2241106
UV protection housing for SC4200c and SC4500 controllers
Sun protection housing for SC controllers.
SKU: LXZ524.99.00005
Tube, culture, 16 x 100 mm, pk/6
High quality 11 ml Hach tubes, supplied without cap.
SKU: 2275806
SKU: 51105600
Molded gray septa 20 mm, PTFE / butyl
20mm molded gray butyl PTFE septa are widely used in the pharmaceutical industry.
SKU: #20PTFE/Butil
2084900 Glass cell for laboratory turbidity meters, 30 ml, 6 pcs. with caps
Glass cuvette for samples. Used for turbidimeters 2100N, 2100AN and Lab RATIO.
SKU: 2084900
UV protection shield for SC4200c and SC4500 controllers
Sun protection panel for SC controllers.
SKU: LXZ524.99.00004
ZEUTEC drawer with rotating cup for coarse samples
The Rotating Cup Drawer for SpectraAlyzer 2.0 analyzers for coarse sample analysis. Used to determine protein, fat and moisture content in such products as grains, cocoa beans, corn, rice, peas, soybeans, animal feed pellets, etc.
SKU: 110-B6003-1
Recommended products
AutoSampler 2.0 for ZEUTEC SpectraAlyzer analyzers
The ZEUTEC AutoSampler 2.0 is used in conjunction with the liquid analysis compartment (Liquid Drawer) of the SpectraAlyzer analyzer. Simplifies compositional analysis of samples using near infrared reflectance characteristics.
SKU: 103-A100-1
Glass square sample cell 25 mm, matched pair
Accessory for spectrophotometers / spectral analysis of liquids.
SKU: 2095000
SKU: 2810 0100
Rectangular plastic cuvette, 10 mm; 100 pieces
Disposable 1.5 ml cuvettes; packing of 100 pieces.
SKU: 2629500
Amtax sc analyzer electrode maintenance kit
The kit contains 3 bottles of electrolyte and 3 membranes for the AMTAX sc ammonium analyzer for ranges 2, 3, 4 (0.05 - 1000 mg/L NH4-N).
SKU: LCW868
Two-layer silicone septa 17.5 mm
17.5 mm PTFE/silicone septa, compatible with 18 mm screw caps and 10 ml and 20 ml chromatography vials. Work on Agilent instruments, CTC PAL, etc.
SKU: #17,5Siiicone
Service kit for BioTector 3500 19-KIT-123
Replacement set for maintenance, interval 6 months.
SKU: 19-KIT-123
UV protection housing for SC4200c and SC4500 controllers
Sun protection housing for SC controllers.
SKU: LXZ524.99.00005
Service kit 19-KIT-130 for BioTector 3500e
Replacement set for maintenance, interval 6 months.
SKU: 19-KIT-130
